Digital I/O#
Communication with digital I/O is a purchasable option and is not part of the standard FlexiBowl®. The input connector of the new generation of FlexiBowl® supports digital and analog signals for direct integration with a PLC without the need for Ethernet communication.
Inputs available on the main connector#
Type |
Signal |
Electrical type |
Active level |
Description |
|---|---|---|---|---|
Standard |
Bit 1 |
Digital |
0–24Vdc, Active High |
Command coding bit (see coding table) |
Standard |
Bit 2 |
Digital |
0–24Vdc, Active High |
Command coding bit |
Standard |
Bit 3 |
Digital |
0–24Vdc, Active High |
Command coding bit |
Standard |
Bit 4 |
Digital |
0–24Vdc, Active High |
Command coding bit |
Standard |
Bit 5 |
Digital |
0–24Vdc, Active High |
Command coding bit |
Standard |
Latch |
Digital |
0–24Vdc, Active High |
Command execution (rising edge) |
Standard |
Empty Sensor |
Digital |
0–24Vdc, Active High |
FlexiBowl® empty detection sensor |
Standard |
Zeroing |
Digital |
0–24Vdc, Active High |
Provision for multi-sector disc fixing sensor |
Option |
Flip proportional valve feedback |
Analog |
0–10Vdc |
Flip proportional valve feedback signal |
Option |
Blow proportional valve feedback |
Analog |
0–10Vdc |
Blow proportional valve feedback signal |
Option |
Strobe Backlight + / − |
— |
— |
External backlight strobe command (diode and fuse protection required) |
Option |
Strobe Backlight 2+ / 2− |
— |
— |
Secondary external backlight strobe command |
STO connector (Safe Torque Off)#
The STO connector is dedicated to the safety function for stopping the motor:
Pin |
Signal |
Description |
|---|---|---|
1 |
STO1+ |
Safe Torque Off 1 |
2 |
STO1- |
STO1 return |
3 |
STO2+ |
Safe Torque Off 2 |
4 |
STO2- |
STO2 return |
5 |
24V |
Power supply |
6 |
0V |
Ground |
Command coding via digital bits (Bit 1–5)#
The 5 digital input bits form a 5-digit binary word that identifies the command to be executed. The command is acquired on the rising edge of the Latch signal.
Binary code (Bit5–Bit1) |
Command |
|---|---|
|
Alarm reset |
|
Exe Seq 1 |
|
Exe Seq 2 |
|
Exe Seq 3 |
|
Exe Seq 4 |
|
Exe Seq 5 |
|
Exe Seq 6 |
|
Exe Seq 7 |
|
Exe Seq 8 |
|
Exe Seq 9 |
|
Exe Seq 10 |
|
Exe Seq 11 |
|
Exe Seq 12 |
|
Exe Seq 13 |
|
Exe Seq 14 |
|
Exe Seq 15 |
|
Exe Seq 16 |
|
Exe Seq 17 |
|
Exe Seq 18 |
|
Exe Seq 19 |
|
Exe Seq 20 |
|
Hopper Activation 1 |
|
Hopper Activation 2 |
|
Hopper Activation 3 |
|
Hopper Activation 4 |
|
Spare |
Tip
Example: to execute Sequence 5, set Bit1=1, Bit2=0, Bit3=1, Bit4=0, Bit5=0 (binary code 00101) and then send a rising edge on Latch.