Transport and handling#

Packaging#

The machine is shipped by ARS S.r.l. from the production plant to that of the user Customer. Depending on the transport distance, the specific requests of the Customer, and the time the load remains in the packaging, the machine is shipped in the following ways:

  • normal protective packaging for short and medium distances;

  • special protective packaging for long distances.

Shipment must be carried out with covered or tarpaulin-covered means of transport, depending on the type of load.

Inspection on arrival#

Note

On receipt of the product, before signing the delivery note:

  1. External inspection of the packaging: Check the integrity of the box and of the outer packaging. Check for any signs of impacts, crushing or wetting.

  2. Contents check: Compare the contents with the delivery note. Check that all the ordered components are present.

In case of damage or discrepancies#

Note

If problems are found:

Packaging dimensions and weights#

Specification

FlexiBowl® 200

FlexiBowl® 350

FlexiBowl® 500/500E

FlexiBowl® 650

FlexiBowl® 800

FlexiBowl® 1200

Gross weight (with packaging)

15 kg

15 kg

15 kg

20 kg

30 kg

40 kg

Crate dimensions (mm)

800x600x552h

800x600x552h

800x600x552h

930x905x505h

1130x1030x515h

1515x1515x605h

Transport and handling of the packaging#

Important

During transport:

  • Always handle the packaging in a vertical position (observe the “UP” arrows on the packaging)

  • Do not drop or knock the package

  • Use trolleys or pallet trucks suited to the weight

  • Avoid sudden temperature changes

Operator qualification

Required PPE

Lifting equipment

Lifting equipment operator

gloves shoes overalls helmet

Forklift with a capacity of no less than 50 kg

Warning

  • Use only suitable, approved lifting equipment compatible with the dimensions and weight of the FlexiBowl®.

  • Make sure nobody is standing within the operating range of the lifting equipment.

To handle the machine body with its packaging, proceed as described:

Step

Operation

1

Position the forks of the forklift under the wooden crate in which the machine is placed.

2

Make sure the forks protrude from the front of the load (by at least 5 cm), for a length sufficient to eliminate any risk of the transported part tipping over.

3

Raise the forks until they contact the load.

Note

If necessary, secure the load to the forks with clamps or similar devices.

4

Slowly raise the load a few tens of centimeters and check its stability, making sure that the center of gravity of the load is positioned in the center of the lifting forks.

5

Tilt the mast backwards (towards the driver’s seat) to take advantage of the overturning moment and ensure greater stability of the load during transport.

6

Adapt the transport speed to the flooring and the type of load, avoiding abrupt maneuvers.

Important

Position the forks of the forklift as shown in the figure

../../_images/muletto.png

Storage#

Tip

During storage:

  • Store in a dry, covered place

  • Do not stack other loads on top of the packaging

  • Do not climb or lean on the packaging

  • Comply with the environmental conditions given in the previous table

Unpacking#

Tip

During unpacking:

  • Open carefully so as not to damage the internal components

  • Keep the original packaging for any returns or future transport

  • Check that all the accessories and the documentation are present

To remove the packaging, proceed as described:

Step

Operation

1

Position the FlexiBowl® in its intended location.

2

Unscrew the FlexiBowl® from the base of the wooden crate used for shipping.

3

Remove the USB device and the test file from the crate. Keep it for later use.

4

Lift the FlexiBowl® and remove it from the crate.

Warning

For the manual lifting operation of the FlexiBowl® from the wooden crate, 2 operators must be present.

For handling the machine and/or its parts, refer to the paragraph “Transport of the FlexiBowl®”.

Disposal of the packaging#

The packaging is an integral part of the supply and is not taken back, so its disposal is the responsibility of the purchaser. Any disposal or destruction must take place in compliance with the regulations in force in the user’s country, taking into account the nature of the materials:

  • wood for the crates;

  • plastic film to protect the machine and adhesive tapes to secure it;

  • bags of moisture-absorbing material;

  • etc.

Transport of the FlexiBowl®#

ARS S.r.l., depending on the mode of transport, uses packaging and fastenings suitable to guarantee integrity and preservation during transport.

On receipt of the machine, check that no part has been damaged during transport and/or handling. If any damage is found, it is mandatory to report it immediately to the Manufacturer.

The handling activities described in this paragraph must be carried out by personnel qualified for such operations: personnel specifically trained to carry out loading, unloading and handling operations safely using lifting equipment, and who are aware of the accident-prevention rules.

Warning

ARS S.r.l. is not liable for damage to property or persons caused by accidents resulting from failure to comply with the instructions given in this manual.

After unpacking, the FlexiBowl® is already fully assembled. Follow the table below for the weights and dimensions of the various models:

Model

Weight

Dimensions

FlexiBowl® 200

7 kg*

Ø240 x 196 mm

FlexiBowl® 350

14 kg*

Ø384 x 234 mm

FlexiBowl® 500

35 kg

668 x 535 x 275 mm

FlexiBowl® 650

51 kg

821 x 694 x 314.50 mm

FlexiBowl® 800

67 kg

973 x 884 x 342 mm

FlexiBowl® 1200

144 kg

1386 x 1240 x 388 mm

Note

Measurement refers to the FlexiBowl® only; the rack for the remote electronics, attached to the sizes referred to, weighs 10 kg.

Warning

The standard EN ISO 11228-1-2022 prohibits manually lifting loads above 25 kg (the limit may be even lower depending on the sex and age of the operator), so, for safety reasons, the use of lifting machines is mandatory for FlexiBowl® units that exceed this limit. The FlexiBowl® units that exceed the 25 kg limit are those of size 500 and above.

FlexiBowl® units of size 500 and above are fitted with lifting eyebolts, to be used to transport the machine from the packing box to its final position.

Important

The eyebolts are fixed on swivel bases: when slinging the FlexiBowl®, it is important to make sure that the load lies in the plane of the eyebolt’s eye and that it does not exceed 45° relative to the vertical axis, a situation that could cause shear loads that would stress the eyebolts abnormally.

../../_images/din580.PNG

Warning

The handles on FlexiBowl® units of size 500 and above are NOT to be used for lifting; they serve only to guide positioning on the machine plane.

Sizing of the lifting ropes#

The diameter of the ropes must be sufficient to support the weight of the FlexiBowl®, while the length must be such as to ensure the correct orientation of the load on the eyebolt according to the principles described above, based on standard DIN 580:

../../_images/FB650sol.PNG

FlexiBowl® model

Minimum cable length A

500

300 mm

650

396 mm

800

495 mm

1200

687 mm